Refer to the following table. There is only one gap in the center of the DIMM slot, and the memory module can be fixed in one direction only. Unlock a DIMM slot by pressing the module clips outward. In order to avoid damaging any devices, make sure that they have been installed properly prior to connecting the power supply. Make sure that the power supply cable and pins are properly aligned with the connector on the motherboard.
Line-in jack, Line-out jack, Microphone jack When using a two-channel sound source, the Line-out jack is used to connect to speakers or headphones; This speed advantage over the conventional 12 Mb on USB 1.
These fans will be automatically turned off after the system enters suspend mode. Page 37 Chapter 2 Installation Instructions Header: HDER Optional The expansion cable can be connected to either the front provided that the front panel of your chassis is equipped with the appropriate interface or real panel of the chassis.
Page 38 Chapter 2 Installation Instructions Wake-Up On Internal Modem: WOM Through this function, the system which is in the suspend or soft-off status can be waked up by a ring signal received form the internal modem. When this function is used, be sure an internal modem card which supports this function is used. These connectors support the thin Serial ATA cables for primary internal storage devices.
Their priority is sequenced from high to low Front Audio to Rear Audio. If headphones are plugged into the front panel of the chassis using the Front Audio , then the Speaker Out Rear Audio on the rear panel will not work. When you install or take out such cards, you must make sure that the power plug has been pulled out.
Note the notches on the card Golden fingers to ensure that they fit the AGP slot on your motherboard. Page Jumpers Chapter 2 Installation Instructions Jumpers The users can change the jumper settings on this motherboard if needed. This section explains how to use the various functions of this motherboard by chang- ing the jumper settings.
Users should read the following contents carefully prior to modifying any jumper settings. How to clear CMOS? Turn off the AC power supply and connect pins 1 and 2 together using the jumper cap. After making all the connections, replace the system case cover. Be sure that all switches are off. Turn on the devices in the following order.
Detailed descriptions of the BIOS parameters are also provided. You have to run the Setup Program when the following cases occur: 1.
An error message appears on the screen during the system POST process. Advanced Chipset Features The values for the chipset can be changed through this menu, and the system performance can be optimized.
Integrated Peripherals All onboard peripherals can be set up through this menu. If any other program writes to this memory area, a system error may result. The available setting values are: Enabled and Disbled.
The avail- able setting values are: Disabled and Enabled. USB 2. The available setting values are: Disabled and Enabled. This item enables you to determine the infrared function of the onboard infrared chip. In other words, it is a standard that describes how computer components work together to manage system hardware. Page 67 Chapter 3 BIOS Description will close, however, the vertical and horizontal scanning movement of the screen continues. The setting values are Disabled and Enabled.
When the temperature of CPU is higher than setting value, the motherboard will send off warning information. The possible settings range from a minimum of 8 to a maximum of Note: This option is invisible for locking frequency CPU. A dialogue box will pop up that allows you to load the default BIOS settings.
The defaults set by BIOS set the basic system functions in order to ensure system stability. Password Disabled!!! Press any key to continue … Page 74 Chapter The utility CD that came with the motherboard contains useful software and several utility drivers that enhance the motherboard features. Norton Internet Security 3. Homepage Click here to visit Foxconn motherboard homepage.
Note: 1. You can select the driver that you want to install and begin the setup steps. Note: The following setup steps are based on Windows XP environment. There may be some differences with other operating systems. Page Install Usb2. Please read the guide carefully and select the relevant installation method. If you want to know further information, please visit our website: www.
You should connect the same number of speakers as the audio chan- nels you will select in the software utility. Description: Selecting 4- or 6-Channel Setting 1. Click the audio icon from the Windows traybar at the bottom of the screen. Click the Speaker Configuration tab.
Click here 4. The following window appears. Click here 5. Select the multi-channel operation you prefer from No. Click OK. Page 84 Chapter 4 Driver CD Introduction Testing the Connected Speakers To ensure 4- or 6-channel audio operation works properly, you may need to test each connected speaker to make sure every speaker works properly. If any speaker fails to sound, then check whether the cable is inserted firmly to the connector or replace the bad speakers with good ones.
Simple and easy to operate, with a user-friendly graphics interface. Page Superlogo The best resolution is x84 for top-right logo and x or x for full screen logo. Page Superupdate 3. Page 96 Chapter 5 Directions for Bundled Software 3. Page 97 Chapter 5 Directions for Bundled Software 6. Page 98 Chapter 5 Directions for Bundled Software 3. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Foxconn M1 Manual Download for 1.
Tested to comply with FCC standards. Signature : Date : You can only view or download manuals with. Sign Up and get 5 for free.
0コメント